DIG's 4-Outlet PC Drip Head Manifold is an emission device used to retrofit a 1/2" sprinkler riser into a four-outlet drip irrigation system without altering the flow of the sprinkler system zone. The 4-Outlet PC Drip Head Manifold is available in four color-coded models and can operate at a pressure range of 10-50 PSI with an even flow per each outlet. It allows installation flexibility when incorporated into a new system or as a part of an existing sprinkler system zone. The barbed outlets are used with 1/4" distribution tubing or 1/4" drip line to deliver water to individual plants or groups of plants.

Features:

• Pressure compensating feature supports consistent flow at operating pressure range from 10 to 50 PSI, providing equal flow from each outlet regardless of pressure fluctuations.
• Color coded base for easy flow rate identification.
• Applies water directly to the plant root zone area, leading to less surface evaporation from leaves and soil.
• Eliminates wet walls and discoloration and staining of fences and windows.
• Designed for new and existing landscapes, including oddly shaped areas where a sprinkler head cannot provide good coverage.
• No special tools or glue are needed.
• Built with a backup screen filter.
• Barbed outlets allow installation flexibility.
• Can be installed above grade or placed below grade in a 6" emitter box.
• Use with any 1/4" distribution tubing or 1/4" dripline.
• Constructed of UV-resistant, durable plastic material to withstand the most adverse.
• 1/2" Female Threaded Inlet.

DIG's 4-Outlet PC Drip Head Manifold is an emission device used to retrofit a 1/2" sprinkler riser into a four-outlet drip irrigation system without altering the flow of the sprinkler system zone. The 4-Outlet PC Drip Head Manifold is available in four color-coded models and can operate at a pressure range of 10-50 PSI with an even flow per each outlet. It allows installation flexibility when incorporated into a new system or as a part of an existing sprinkler system zone. The barbed outlets are used with 1/4" distribution tubing or 1/4" drip line to deliver water to individual plants or groups of plants.

Features:

• Pressure compensating feature supports consistent flow at operating pressure range from 10 to 50 PSI, providing equal flow from each outlet regardless of pressure fluctuations.
• Color coded base for easy flow rate identification.
• Applies water directly to the plant root zone area, leading to less surface evaporation from leaves and soil.
• Eliminates wet walls and discoloration and staining of fences and windows.
• Designed for new and existing landscapes, including oddly shaped areas where a sprinkler head cannot provide good coverage.
• No special tools or glue are needed.
• Built with a backup screen filter.
• Barbed outlets allow installation flexibility.
• Can be installed above grade or placed below grade in a 6" emitter box.
• Use with any 1/4" distribution tubing or 1/4" dripline.
• Constructed of UV-resistant, durable plastic material to withstand the most adverse.
• 1/2" Female Threaded Inlet.

Converts an existing 1/2" sprinkler riser to a 6-outlet, adjustable high-flow drip system with a flow rate 0 to 20 GPH per zone. The 6-outlet drip manifold operates at any pressure between 15 to 50 PSI. It may be used with 1/4" micro tubing, 1/4" dripline or with individual drippers.

FEATURES:

• Swivel barbed outlets allow installation flexibility and protection of flow control
• Made of rugged materials to withstand adverse conditions
• Can be installed above or below grade in a 6" (15 cm) emitter box
• Use with 1/4" (.150" -.170" ID (4 mm ID) distribution tubing or with 1/4" (4 mm) dripline

SPECIFICATIONS:

• Flow rate is adjustable between 0-20 GPH (0-75 L/H) per each outlet
• Operating pressure: 15-50 PSI (3.5 BAR)
• Temperature range: up to 122°F (50°C)
• Inlet size: 1/2" female pipe thread (FNPT)
• Outlets size: 1/4" barbed mini valve
• Accepts 1/4” distribution tubing with .150" to .170" ID and 1/4" drip line
• Filter requirement: minimum of 40 mesh
• Materials:
  • Body and cover: high-impact plastic
  • Barbed valve: high-impact plastic
  • Diaphragm: EPDM ###
  • Dimensions: 2.25" W x 1.5" H (57 mm W x 38 mm H)

** High water temperature in a micro irrigation lateral
will influence the flow discharge.

DIG’s TOP 12-outlet drip manifold utilizes extremely accurate, pressure compensating individual and interchangeable drip emitters to ensure equal flow from each outlet over a wide range of operating pressures from 10 to 80 PSI. Available with .6, 1, 2 and 3.3 GPH per outlet, the TOP can deliver water directly to up to 12 plants with less water evaporation and wind-drift than the overhead sprinkler heads it replaces. Using the TOP can save a significant amount of water by improving irrigation efficiency and lowering water runoff.

Features:

• Constructed with 12 built-in individually pressure compensating drip emitters
• Self-flushing emitters allow passage of water and minimize clogging
• Interchangeable drip emitters for variable flow rates in a single head
• Color-coded drip emitters and barbs easily identify flow rate at each zone
• Each drip emitter individually filtered (approx. 80 mesh)
• Backup mini disk filter
• Rugged materials to withstand the most adverse conditions
• Install above grade or place below grade in a 6” emitter box
• Inlet plugs provide the option to cap off up to eight drip emitters

Note: If using 1/4 tubing you must purchase (DR-40050) converter adapters.

DIG’s TOP 12-outlet drip manifold utilizes extremely accurate, pressure compensating individual and interchangeable drip emitters to ensure equal flow from each outlet over a wide range of operating pressures from 10 to 80 PSI. Available with .6, 1, 2 and 3.3 GPH per outlet, the TOP can deliver water directly to up to 12 plants with less water evaporation and wind-drift than the overhead sprinkler heads it replaces. Using the TOP can save a significant amount of water by improving irrigation efficiency and lowering water runoff.

Features:

• Constructed with 12 built-in individually pressure compensating drip emitters
• Self-flushing emitters allow passage of water and minimize clogging
• Interchangeable drip emitters for variable flow rates in a single head
• Color-coded drip emitters and barbs easily identify flow rate at each zone
• Each drip emitter individually filtered (approx. 80 mesh)
• Backup mini disk filter
• Rugged materials to withstand the most adverse conditions
• Install above grade or place below grade in a 6” emitter box
• Inlet plugs provide the option to cap off up to eight drip emitters

Note: If using 1/4" tubing you must purchase (DR-40050) converter adapter.

DIG’s TOP 12-outlet drip manifold utilizes extremely accurate, pressure compensating individual and interchangeable drip emitters to ensure equal flow from each outlet over a wide range of operating pressures from 10 to 80 PSI. Available with .6, 1, 2 and 3.3 GPH per outlet, the TOP can deliver water directly to up to 12 plants with less water evaporation and wind-drift than the overhead sprinkler heads it replaces. Using the TOP can save a significant amount of water by improving irrigation efficiency and lowering water runoff.

Features:

• Constructed with 12 built-in individually pressure compensating drip emitters
• Self-flushing emitters allow passage of water and minimize clogging
• Interchangeable drip emitters for variable flow rates in a single head
• Color-coded drip emitters and barbs easily identify flow rate at each zone
• Each drip emitter individually filtered (approx. 80 mesh)
• Backup mini disk filter
• Rugged materials to withstand the most adverse conditions
• Install above grade or place below grade in a 6” emitter box
• Inlet plugs provide the option to cap off up to eight drip emitters

Note: If using 1/4" tubing you must purchase (DR-40050) converter adapter.

DIG’s TOP 12-outlet drip manifold utilizes extremely accurate, pressure compensating individual and interchangeable drip emitters to ensure equal flow from each outlet over a wide range of operating pressures from 10 to 80 PSI. Available with .6, 1, 2 and 3.3 GPH per outlet, the TOP can deliver water directly to up to 12 plants with less water evaporation and wind-drift than the overhead sprinkler heads it replaces. Using the TOP can save a significant amount of water by improving irrigation efficiency and lowering water runoff.

Features:

• Constructed with 12 built-in individually pressure compensating drip emitters
• Self-flushing emitters allow passage of water and minimize clogging
• Interchangeable drip emitters for variable flow rates in a single head
• Color-coded drip emitters and barbs easily identify flow rate at each zone
• Each drip emitter individually filtered (approx. 80 mesh)
• Backup mini disk filter
• Rugged materials to withstand the most adverse conditions
• Install above grade or place below grade in a 6” emitter box
• Inlet plugs provide the option to cap off up to eight drip emitters

Note: If using 1/4" tubing you must purchase (DR-40050) converter adapter.

Converter Barb 1/8" to 1/4"

1/4" converter barb is only necessary if 1/4" micro tubing is used. The converter has a compression side to be inserted into the drip head body. The other side is a 1/4" barb to 1/4" micro tubing.

DIG’s TOP 12-outlet drip manifold utilizes extremely accurate, pressure compensating individual and interchangeable drip emitters to ensure equal flow from each outlet over a wide range of operating pressures from 10 to 80 PSI. Available with .6, 1, 2 and 3.3 GPH.

Features:

• Interchangeable drip emitters for variable flow rates in a single head
• Color-coded drip emitters and barbs easily identify flow rate at each zone
• Each drip emitter individually filtered (approx. 80 mesh)

DIG’s TOP 12-outlet drip manifold utilizes extremely accurate, pressure compensating individual and interchangeable drip emitters to ensure equal flow from each outlet over a wide range of operating pressures from 10 to 80 PSI. Available with .6, 1, 2 and 3.3 GPH.

Features:

• Interchangeable drip emitters for variable flow rates in a single head
• Color-coded drip emitters and barbs easily identify flow rate at each zone
• Each drip emitter individually filtered (approx. 80 mesh)

DIG’s TOP 12-outlet drip manifold utilizes extremely accurate, pressure compensating individual and interchangeable drip emitters to ensure equal flow from each outlet over a wide range of operating pressures from 10 to 80 PSI. Available with .6, 1, 2 and 3.3 GPH.

Features:

• Interchangeable drip emitters for variable flow rates in a single head
• Color-coded drip emitters and barbs easily identify flow rate at each zone
• Each drip emitter individually filtered (approx. 80 mesh)

DIG’s TOP 12-outlet drip manifold utilizes extremely accurate, pressure compensating individual and interchangeable drip emitters to ensure equal flow from each outlet over a wide range of operating pressures from 10 to 80 PSI. Available with .6, 1, 2 and 3.3 GPH.

Features:

• Interchangeable drip emitters for variable flow rates in a single head
• Color-coded drip emitters and barbs easily identify flow rate at each zone
• Each drip emitter individually filtered (approx. 80 mesh)